Accessories for CENTRO Gripp 125

Basis jaw movable, pivot jaw
Order-no: 2334/125

 serve to accommodate various grip studs
 material: hardened steel
 side surfaces (hardened, ground and polished)
    can also be used for clamping
 grip studs are not included in the scope of delivery

Technical data >> 

Carrier jaw mobile
Order-no: 2313/125

 serve to accommodate the universal gripp set
 material: hardened steel
 side surface (hardened, ground and polished)
    can also be used for clamping
 for clamping of workpieces that are not parallel
 for clamping of irregular workpieces
 gripp set is not included in the scope of delivery

Technical data >> 

Universal pull-down jaw movable
Order-no: 2342/125

 pull-down with ground and polished spring
    leaves for unmachined and machined
    clamping surfaces
 material: hardened steel
 ground and polished clamping surfaces   
 reduced-width jaws, 90 mm
 high clamping accuracy for parallel and
    accurate angle machining
 click system on high side

Technical data >> 

Step jaw movable
Order-no: 2331/125

 for clamping of parallel pre-worked square
    workpieces
 material: hardened steel
 clamping surfaces are carbide coated (80 Rockwell) 
    for higher grip factor - higher holding force by a factor of 2
    
Technical data >> 

High jaw with reduced width 64 mm, movable
Order-no: 2311/125

 allows an optimal access to the workpiece - 
    ideal also for short tools
 for clamping of small up to medium sized workpieces
 clamping of raw parts (also raw parts) is possible
    by 2 adjustable grip studs per jaw
    (grip studs are not included in the sope of delievery)
 smooth clamping surfaces for clamping of pe-worked
    square workpieces

Technical data >> 

High jaw with reduced width 20 mm,
carbide coated, movable
Order-no: 2321/125

 for clamping of pre-worked square workpieces 
    as well as small workpieces  
 further improved accessibility to the workpiece
    thanks to narrow and high mounting form -
    ideal also for short tools
 clamping surfaces are additionally carbide coated 
    (80 Rockwell) for higher grip factor - higher holding
    force by a factor of 2

Technical data >> 

Console
Order-no: 2340/125

 for improvement of accessibility by 5-sided machining

Scope of supply:
Console incl. fixing bolts, 2 key ways, 4 screws

Attention:
The mounting hole pattern of CENTRO Gripp and console is offset slightly in order to enable mounting in tables with parallel T-slots as well as in tables with cross slots.

Technical data >>

Spring leaves (pair)
Order-no: 2534/090

 hardened spring leaves
 spring leaves (spare) for the pull-down
    jaws

Universal gripp set
Order-no. 2306/000

 for clamping of complex workpieces
scope of delivery:
    - 4 x Grip stud 2306/001
    - 4 x Basic unit 2306/002
    - 4 x Support 2306/003
    - fastening screws M10 in various lenghts    
    - 4 x Spacers
    - 4 x Support screws

Prismatic  gripper
Order-no. 2305/000

 with his special shape it reduces the
    applied clamping force
 replaces the "round grip" of the universal
    grip set

Grip stud
Order-no. 2306/001

 Grip stud for universal "grip" set

Basic unit
Order-no. 2306/002

 Basic unit for universal "grip" set

Support 
Order-no. 2306/003

 Support for universal "grip" set

Grip stud insert with spiked ends
Order-no: 2301/000

 for clamping of raw parts
 grip engagement height: adjustable form
     4,5 to 6,0 mm

Clamping insert flat
Order-no: 2302/000

 with carbide coating for clamping of
    pre-worked workpieces

Round grip stud with spiked ends
Order-no: 2303/000

 for machining of raw parts
 provides 6 mm space under the workpiece

Parallels, Click (pair)
Order-no: 3550/090 

 For parallel raising of workpieces
 Bolt-on parallels with Click system
 Hardened and ground parallels
 For the high side of the jaws
 
Technical data >> 

Workpiece stop
Order-no: 2401/000 

 it can be fittet on either side of the NC vice
    at the positions provided
 preadjustable position of the 3rd workpiece axis
 after clamping the workpiece, the workpiece stop
    can be swivelled away with a single movement.
    It is then also possible to machine the stopping side
    of the workpiece; (Repeating accuracy: + 0,01)

Technical data >> 

Workpiece stop
Order-no: 2402/000 

 pre-mountable with different fix distances
    (see drawing)
 fixable position of the 3rd workpiece axis
 after positioning and clamping of the workpiece,
     the workpiece stop can be swivelled away

Technical data >> 

Aligning and fixing set
Order-no see technical data

 for aligning (positioning) and fixing of vices
    on pallets and machine tables
 size according to T-slot or thread in the machine
    table

Technical data >> 

Torque wrench
Order-no: 2601/000

can be preset to 20 - 120 Nm
only for operation of the CENTRO Gripp high pressure gripper spindle
use a smaller torque wrench for more precise
    presetting of the spindle power

Technical data >>